Robotics is the engineering science and technology of robots, and their design, manufacture, application, and structural disposition. Robotics is related to electronics, mechanics, and software. The word robot was introduced to the public by Czech writer Karel ÄŒapek in his play R.U.R. (Rossum's Universal Robots), published in 1920. The term "robotics" was coined by Isaac Asimov in his 1941 science fiction short-story "Liar!"
A robot leg powered by Air Muscles
Actuators are like the "muscles" of a robot, the parts which convert stored energy into movement. By far the most popular actuators are electric motors that spin a wheel or gear, and linear actuators that control industrial robots in factors. But there are some recent advances in alternative types of actuators, powered by electricity, chemicals, or compressed air:
Electric motors: The vast majority of robots use electric motors, often brushed and brushless DC motors in portable robots or AC motors in industrial robots and CNC machines.
Get your grade
or your money back
using our Essay Writing Service!
Linear Actuators: Various types of linear actuators move in and out instead of by spinning, particularly when very large forces are needed such as with industrial robotics. They are typically powered by compressed air (pneumatic actuator) or an oil (hydraulic actuator).
Series Elastic Actuators: A spring can be designed as part of the motor actuator, to allow improved force control. It has been used in various robots, particularly walking humanoid robots.
Air muscles: (Also known as Pneumatic Artificial Muscles) are special tubes that contract (typically up to 40%) when air is forced inside it. They have been used for some robot applications.
Muscle wire: (Also known as Shape Memory Alloy, Nitinol or Flexinol Wire) is a material that contracts slightly (typically under 5%) when electricity is run through it. They have been used for some small robot applications.
Electroactive Polymers: (EAPs or EPAMs) are a new plastic material that can contract quite significantly (up to 400%) from electricity, and have been used in facial muscles and arms of humanoid robots, and to allow new robots to float, fly, swim or walk.
Piezo motor: A recent alternative to DC motors are piezo motors or ultrasonic motors. These work on a fundamentally different principle, whereby tiny piezoceramic elements, vibrating many thousands of times per second, cause linear or rotary motion. There are different mechanisms of operation; one type uses the vibration of the piezo elements to walk the motor in a circle or a straight line. Another type uses the piezo elements to cause a nut to vibrate and drive a screw. The advantages of these motors are nanometer resolution, speed, and available force for their size. These motors are already available commercially, and being used on some robots.[
Elastic nanotubes: These are a promising, early-stage experimental technology. The absence of defects in nanotubes enables these filaments to deform elastically by several percent, with energy storage levels of perhaps 10Â J/cm3 for metal nanotubes. Human biceps could be replaced with an 8Â mm diameter wire of this material. Such compact "muscle" might allow future robots to outrun and outjump humans.
Current robotic and prosthetic hands receive far less tactile information than the human hand. Recent research has developed a tactile sensor array that mimics the mechanical properties and touch receptors of human fingertips. The sensor array is constructed as a rigid core surrounded by conductive fluid contained by an elastomeric skin. Electrodes are mounted on the surface of the rigid core and are connected to an impedance-measuring device within the core. When the artificial skin touches an object the fluid path around the electrodes is deformed, producing impedance changes that map the forces received from the object. The researchers expect that an important function of such artificial fingertips will be adjusting robotic grip on held objects.
In 2009, scientists from several European countries and Israel developed a prosthetic hand, called SmartHand, which functions like a real one, allowing patients to write with it, type on a keyboard, play piano and perform other fine movements. The prosthesis has sensors which enable the patient to sense real feeling in its fingertips.
Always on Time
Marked to Standard
Computer vision is the science and technology of machines that see. As a scientific discipline, computer vision is concerned with the theory behind artificial systems that extract information from images. The image data can take many forms, such as video sequences and views from cameras.
In most practical computer vision applications, the computers are pre-programmed to solve a particular task, but methods based on learning are now becoming increasingly common.
Computer vision systems rely on image sensors which detect electromagnetic radiation which is typically in the form of either visible light or infra-red light. The sensors are designed using solid-state physics. The process by which light propagates and reflects off surfaces is explained using optics. Sophisticated image sensors even require quantum mechanics to provide a complete understanding of the image formation process.
There is a subfield within computer vision where artificial systems are designed to mimic the processing and behavior of biological systems, at different levels of complexity. Also, some of the learning-based methods developed within computer vision have their background in biology.
Robots which must work in the real world require some way to manipulate objects; pick up, modify, destroy, or otherwise have an effect. Thus the 'hands' of a robot are often referred to as end effectors, while the arm is referred to as a manipulator. Most robot arms have replaceable effectors, each allowing them to perform some small range of tasks. Some have a fixed manipulator which cannot be replaced, while a few have one very general purpose manipulator, for example a humanoid hand.
Mechanical Grippers: One of the most common effectors is the gripper. In its simplest manifestation it consists of just two fingers which can open and close to pick up and let go of a range of small objects. Fingers can for example be made of a chain with a metal wire run trough it.See Shadow Hand.
Vacuum Grippers: Pick and place robots for electronic components and for large objects like car windscreens, will often use very simple vacuum grippers. These are very simple astrictive devices, but can hold very large loads provided the prehension surface is smooth enough to ensure suction.
General purpose effectors: Some advanced robots are beginning to use fully humanoid hands, like the Shadow Hand, MANUS, and the Schunk hand. These highly dexterous manipulators, with as many as 20 degrees of freedom and hundreds of tactile sensors.
For the definitive guide to all forms of robot endeffectors, their design, and usage consult the book "Robot Grippers".
Segway in the Robot museum in Nagoya.
For simplicity, most mobile robots have four wheels. However, some researchers have tried to create more complex wheeled robots, with only one or two wheels. These can have certain advantages such as greater efficiency, reduced parts, and allow a robot to navigate in tight places that a four wheeled robot would not be able to.
Two-wheeled balancing: Balancing robots generally use a Gyroscope to detect how much a robot is falling and then drive the wheels proportionally in the opposite direction, to counter-balance the fall at hundreds of times per second, based on the dynamics of an inverted pendulum. Many different balancing robots have been designed. While the Segway is not commonly thought of as a robot, it can be thought of as a component of a robot, such as NASA's Robonaut that has been mounted on a Segway.
One-wheeled balancing: A one-wheeled balancing robot is an extension of a two-wheeled balancing robot so that it can move in any 2D direction using a round ball as its only wheel. Several one-wheeled balancing robots have been designed recently, such as Carnegie Mellon University's "Ballbot" that is the approximate height and width of a person, and Tohoku Gakuin University's "BallIP". Because of the long, thin shape and ability to maneuver in tight spaces, they have the potential to function better than other robots in environments with people.
Spherical orb robots: Several attempts have been made in robots that are completely inside a spherical ball, either by spinning a weight inside the ball, or by rotating the outer shells of the sphere. These have also been referred to as an orb bot or a ball bot
This Essay is
a Student's Work
This essay has been submitted by a student. This is not an example of the work written by our professional essay writers.Examples of our work
Six-wheeled robots: Using six wheels instead of four wheels can give better traction or grip in outdoor terrain such as on rocky dirt or grass.
Tracked robots: Tank tracks provide even more traction than a six-wheeled robot. Tracked wheels behave as if they were made of hundreds of wheels, therefore are very common for outdoor and military robots, where the robot must drive on very rough terrain. However, they are difficult to use indoors such as on carpets and smooth floors. Examples include NASA's Urban Robot "Urbie".
iCub robot, designed by the RobotCub Consortium
Walking is a difficult and dynamic problem to solve. Several robots have been made which can walk reliably on two legs, however none have yet been made which are as robust as a human. Many other robots have been built that walk on more than two legs, due to these robots being significantly easier to construct. Hybrids too have been proposed in movies such as I, Robot, where they walk on 2 legs and switch to 4 (arms+legs) when going to a sprint. Typically, robots on 2 legs can walk well on flat floors, and can occasionally walk up stairs. None can walk over rocky, uneven terrain. Some of the methods which have been tried are:
ZMP Technique: The Zero Moment Point (ZMP) is the algorithm used by robots such as Honda's ASIMO. The robot's onboard computer tries to keep the total inertial forces (the combination of earth's gravity and the acceleration and deceleration of walking), exactly opposed by the floor reaction force (the force of the floor pushing back on the robot's foot). In this way, the two forces cancel out, leaving no moment (force causing the robot to rotate and fall over). However, this is not exactly how a human walks, and the difference is quite apparent to human observers, some of whom have pointed out that ASIMO walks as if it needs the lavatory. ASIMO's walking algorithm is not static, and some dynamic balancing is used (See below). However, it still requires a smooth surface to walk on.
Hopping: Several robots, built in the 1980s by Marc Raibert at the MIT Leg Laboratory, successfully demonstrated very dynamic walking. Initially, a robot with only one leg, and a very small foot, could stay upright simply by hopping. The movement is the same as that of a person on a pogo stick. As the robot falls to one side, it would jump slightly in that direction, in order to catch itself. Soon, the algorithm was generalised to two and four legs. A bipedal robot was demonstrated running and even performing somersaults. A quadruped was also demonstrated which could trot, run, pace, and bound. For a full list of these robots, see the MIT Leg Lab Robots page.
Dynamic Balancing or controlled falling: A more advanced way for a robot to walk is by using a dynamic balancing algorithm, which is potentially more robust than the Zero Moment Point technique, as it constantly monitors the robot's motion, and places the feet in order to maintain stability. This technique was recently demonstrated by Anybots' Dexter Robot, which is so stable, it can even jump. Another example is the TU Delft Flame.
Passive Dynamics: Perhaps the most promising approach utilizes passive dynamics where the momentum of swinging limbs is used for greater efficiency. It has been shown that totally unpowered humanoid mechanisms can walk down a gentle slope, using only gravity to propel themselves. Using this technique, a robot need only supply a small amount of motor power to walk along a flat surface or a little more to walk up a hill. This technique promises to make walking robots at least ten times more efficient than ZMP walkers, like ASIMO.
Other methods of locomotion
Flying: A modern passenger airliner is essentially a flying robot, with two humans to manage it. The autopilot can control the plane for each stage of the journey, including takeoff, normal flight, and even landing. Other flying robots are uninhabited, and are known as unmanned aerial vehicles (UAVs). They can be smaller and lighter without a human pilot onboard, and fly into dangerous territory for military surveillance missions. Some can even fire on targets under command. UAVs are also being developed which can fire on targets automatically, without the need for a command from a human.
Environmental interaction and navigation
Though a significant percentage of robots in commission today are either human controlled, or operate in a static environment, there is an increasing interest in robots that can operate autonomously in a dynamic environment. These robots require some combination of navigation hardware and software in order to traverse their environment. In particular unforeseen events (e.g. people and other obstacles that are not stationary) can cause problems or collisions. Some highly advanced robots as ASIMO, EveR-1, Meinü robot have particularly good robot navigation hardware and software. Also, self-controlled cars, Ernst Dickmanns' driverless car, and the entries in the DARPA Grand Challenge, are capable of sensing the environment well and subsequently making navigational decisions based on this information. Most of these robots employ a GPS navigation device with waypoints, along with radar, sometimes combined with other sensory data such as LIDAR, video cameras, and inertial guidance systems for better navigation between waypoints.
Kismet can produce a range of facial expressions.
If robots are to work effectively in homes and other non-industrial environments, the way they are instructed to perform their jobs, and especially how they will be told to stop will be of critical importance. The people who interact with them may have little or no training in robotics, and so any interface will need to be extremely intuitive. Science fiction authors also typically assume that robots will eventually be capable of communicating with humans through speech, gestures, and facial expressions, rather than a command-line interface. Although speech would be the most natural way for the human to communicate, it is quite unnatural for the robot. It will be quite a while before robots interact as naturally as the fictional C-3PO.
Speech recognition: Interpreting the continuous flow of sounds coming from a human (speech recognition), in real time, is a difficult task for a computer, mostly because of the great variability of speech. The same word, spoken by the same person may sound different depending on local acoustics, volume, the previous word, whether or not the speaker has a cold, etc.. It becomes even harder when the speaker has a different accent. Nevertheless, great strides have been made in the field since Davis, Biddulph, and Balashek designed the first "voice input system" which recognized "ten digits spoken by a single user with 100% accuracy" in 1952. Currently, the best systems can recognize continuous, natural speech, up to 160 words per minute, with an accuracy of 95%.
Gestures: One can imagine, in the future, explaining to a robot chef how to make a pastry, or asking directions from a robot police officer. On both of these occasions, making hand gestures would aid the verbal descriptions. In the first case, the robot would be recognizing gestures made by the human, and perhaps repeating them for confirmation. In the second case, the robot police officer would gesture to indicate "down the road, then turn right". It is quite likely that gestures will make up a part of the interaction between humans and robots. A great many systems have been developed to recognize human hand gestures.
Future aspects of robotics
Universities offer Bachelors and Masters degrees in the field of robotics. Select Private Career Colleges and vocational schools offer robotics training to train individuals towards being job ready and employable in the emerging robotics industry.
Employment in roboticsics
A robot technician builds small all-terrain robots. (Courtesy: MobileRobots Inc)
Robotics is an essential component in any modern manufacturing environment. As factories increase their use of robots, the number of robotics related jobs grow and have been observed to be on a steady rise.
Applications of robotics
Script Pro manufactures a robot designed to help pharmacies fill prescriptions that consist of oral solids or medications in pill form. The pharmacist or pharmacy technician enters the prescription information into its information system. The system, upon determining whether or not the drug is in the robot, will send the information to the robot for filling. The robot has 3 different size vials to fill determined by the size of the pill. The robot technician, user, or pharmacist determines the needed size of the vial based on the tablet when the robot is stocked. Once the vial is filled it is brought up to a conveyor belt that delivers it to a holder that spins the vial and attaches the patient label. Afterwards it is set on another conveyor that delivers the patient's medication vial to a slot labeled with the patient's name on an LED read out. The pharmacist or technician then checks the contents of the vial to ensure it's the correct drug for the correct patient and then seals the vials and sends it out front to be picked up. The robot is a very time efficient device that the pharmacy depends on to fill prescriptions.
McKesson's Robot RX is another healthcare robotics product that helps pharmacies dispense thousands of medications daily with little or no errors. The robot can be ten feet wide and thirty feet long and can hold hundreds of different kinds of medications and thousands of doses. The pharmacy saves many resources like staff members that are otherwise unavailable in a resource scarce industry. It uses an electromechanical head coupled with a pneumatic system to capture barcode technology to verify its pulling the correct drug. It then delivers the drug to a patient specific bin on a conveyor belt. Once the bin is filled with all of the drugs that a particular patient needs and that the robot stocks, the bin is then released and returned out on the conveyor belt to a technician waiting to load it into a cart for delivery to the floor.